Anthem D2v Processor

The D2 is designed and built in North America, on the same state-of-the-art high-end platform as its critically acclaimed predecessor, the D1.

However, this next-generation audio/video processor ushers in a new era of digital video performance. With the unparalleled flexibility you have come to expect from Anthem™ processors, it gives you the versatility and adjustability you need to make all of your digital video components work together seamlessly. And the results are spectacular.

Rear Panel View: Anthem D2v Processor

VIDEO SWITCHING

Bandwidth: Composite and S-Video 70 MHz
Component Y 110 MHz
Component Pr 90 MHz
Component Pb 80 MHz

ANALOG AUDIO

Input Impedance: 20 kΩ
Output Impedance: Main-RCA 300 Ω
XLR 600 Ω
Zones 2/3 and Record 51 Ω
Rated Input: 2.0 Vrms
Maximum Input: 5.3 Vrms
Minimum Load: 5 kΩ
Rated Output: 2.0 Vrms
Maximum Output: RCA 6.3 Vrms
XLR 12.6 Vrms
Headphone Output: 100 mW into 32 Ω at 0.2% THD+N
Volume Control Range: Main - 95.5 dB to +31.5 dB (in 0.5 dB increments)
Zone 2/3 and Headphone - 62.5 dB to +10.0 dB (in 1.25 dB increments)
Crosstalk: 82 dB between channels; 86 dB between inputs
XLR Pin Configuration: Pin 1: Ground, Pin 2: Positive, Pin 3: Negative

DIGITAL AUDIO

Crossover: Low-Pass Slope (subwoofer): 24 dB/octave (4th order)
Frequency (adjustable): 25 Hz to 160 Hz (in 5 Hz increments)
Tone Control: Filter Type Shelf
Range +/- 12 dB
Bass Turnover Frequency 200 Hz
Treble Turnover Frequency 2 kHz
S/N Ratio: 100 dB

MAIN PATH

Frequency Response: Analog Direct Inputs: 10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 130 kHz (+0 -3 dB)
Analog-DSP Inputs at 24/96: 10 Hz to 20 kHz (+0 -0.3 dB), 2 Hz to 44.1 kHz (+0 -3 dB)
Digital Inputs at 24/96: 10 Hz to 20 kHz (+0 -0.2 dB), 1 Hz to 45 kHz (+0 -3 dB)
THD+N: Analog Direct Inputs 0.006% (80 kHz BW)
Analog-DSP Inputs at 24/48 or 24/96 0.004% (AES17 Filter)
Digital Inputs at 24/48 or 24/96 0.004% (AES17 Filter)
IMD: Analog Direct Inputs < 0.001%
Analog-DSP Inputs at 24/48 0.001%
Digital Inputs at 24/48 or 24/960.001%
S/N Ratio: Analog Direct Inputs 107 dB
Analog-DSP Inputs at 24/48 or 24/96 101 dB
Digital Inputs at 24/48 or 24/96 104 dB

ZONE 2 & 3 PATHS

Frequency Response: 20 Hz to 20 kHz (+0 -0.1 dB), 3 Hz to 140 kHz (+0 -3 dB)
THD+N: 0.06% (80 kHz BW)
IMD: 0.06%
S/N Ratio: 97 dB

FM TUNER

Sensitivity: 50 dB S/N 13 dBµ typical, 25 dBµ max.
IHF 10 dBµ typical, 20 dBµ max.
S/N Ratio: Mono 75 dB typical, 65 dB min.
Stereo 69 dB typical, 60 dB min.
Distortion: Mono 0.2% typical, 1.0% max.
Stereo 0.3% typical, 1.5% max.
Stereo Separation: 40 dB typical, 25 dB min.
Alternate Channel Selectivity: 70 dB typical, 60 dB min.
Frequency Response: 25 Hz to 15 kHz (+0 -2 dB)

AM TUNER

Sensitivity: 49 dBµ typical, 56 dBµ max.
S/N Ratio: 50 dB typical, 43 dB min.
Distortion: 0.7% typical, 2.0% max.
One-Signal Selectivit: 24 dB typical, 18 dB min.

CONTROL

Infra Red: Carrier Frequency 38 kHz
Maximum 12 V Supply Current 150 mA
Maximum Emitter Current 60 mA per output
RS-232 Interface: Connection DB-9F, straight-wired
Pinout (D2v side) Pin 2: Tx, Pin 3: Rx, Pin 5: Ground
Baud Rate 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200
Configuration 8 data bits, 1 stop bit, no parity bits, flow control(RTS/CTS, none)
Trigger Outputs: Polarity tip positive, sleeve ground
Maximum Current at 12 VDC 300 mA between all three triggers
Sequential Delay 250 ms

POWER REQUIREMENT

Consumption: Maximum 170 W

DIMENSIONS

Height: 5-7/8 inches (14.9 cm) including feet;
rack-mounting: 3 rack units without feet
Width: Standard version 19-1/4 inches (49 cm)
Rack-Mount version 19 inches (48.3 cm)
No-Handle version 17-1/4 inches (43.8 cm)
Depth: 15-1/4 inches (38.7 cm)
Weight: 27 lb (12.3 kg)

AVAILABLE FINISH:

Black